Air Conditioner Condensing Unit

The air conditioner condensing unit is one half of the cooling cycle with the evaporator coil. The condensing unit's job is to diffuse and reject heat, while the evaporator coil absorbs heat. All HVAC technicians learn this as the first step in their cooling education. The condenser is located in the big boxy exterior unit at most buildings. Heat pumps also use condensers, but most people North of Denver do not use heat pumps because the efficiency of heat pumps decreases as the temperature drops.

The condenser along with the compressor is the main transferor of heat between the outside air and the air blowing through your house. To do this, the compressor must be sealed inside the cooling cycle, and that is why compressor replacements are so common. It is very hard to try and repair something that is sealed within the system. On the other hand, there are many things you can do to try and maintain the life of your condensing unit. If not properly maintained, the condenser and most other air conditioning parts will go into a downward spiral before they self destruct. As the parts become worn and less efficient, the compressor and blower motor will start working harder to try and keep cooling despite reduced ability. Eventually parts overheat and fail.

One thing you can do to maintain your Denver HVAC system to to check the outside cooling unit before summer starts and it is in heavy use. I recommend calling a Denver air conditioner company to perform the check, but if you feel handy and know how to operate around electricity, then go ahead. The first step before doing any work on a condensing unit is to shut of the breaker supplying electricity to the unit. Spin the fan and see if it turns. Then turn on the power and switch on the thermostat and make sure the fan starts blowing upward a good deal. A common problem with these condenser motors is bearing failure, which will stop the fan from spinning properly.

The main reason you want to check the condenser fan motor before you operate the system is because it is connected to the compressor. A failure at the fan can overload the compressor, and the compressor is a much more expensive part than the condenser motor.

Just like evaporator coils, condenser coils can build up dirt and gunk which will decrease efficiency. Just like everything else in central air, as efficiency goes down, the system tries to work harder to compensate until it fails. The solution is to call an air conditioning services Denver company to clean the condenser coils. You can also do it yourself, but you will need to turn the thermostat and breaker off and pull the plug on the condenser electrical box. You will need to spray the condenser with enough pressure to remove dirt without bending the fins. A little soap can help too. The key to maintaining performance with these units is maximizing airflow. So the condenser should be clean and the exterior unit should have clear airflow.

EPA Standards for HVAC Equipment

The majority of the US is in a temperate climate. This means that although the temperature does not reach extremes found in tropical and arctic latitudes, there are major seasonal weather variations. Most Americans choose to use a central air or HVAC system to control interior temperature. For large HVAC jobs like schools and warehouses, the cost of ventilation means that careful planning must go into designing the systems. Average temperatures, energy savings, humidity, local and national codes and indoor air quality are just some of the factors that most be considered on public works projects.

The first step for a large building is using central air handling units, instead of individual ventilators in each room. In some instances like a isolated field house, a unit air conditioner may be a better choice because they take up less floor or roof space. Individual units are harder to maintain in a group and cause other ventilation and moisture problems when combined with a central unit. Central heating is especially popular with teachers because it is quieter and therefore they do not mind using it in the classroom. Denver air conditioning companies installed central heat in Denver high schools over 30 years ago and the system has been a success. Central heat is less prone to drafts because of multiple sources of air. A professional HVAC company can maintain a central unit and tweak the global settings to control humidity.

The consolidated design of central units allow them to be serviced without disturbing the work in a building- and they generally take up less interior space. To meet EPA certification for government buildings, HVAC systems must meet certain requirements. Coils must have sloped non corrosive drain pans to prevent water from stagnating or rusting the system interior. They should be in a wall cabinet with easy access that also reduces sound. This means double wall replacement doors with tight seals. EPA filters are always at least two inches thick. A well designed filter bank will take these high performance filters over a large area for max lifetime. Air filter monitors notify Denver HVAC techs when to replace the filters, as well as any major problems in the system.

To maintain indoor air quality, the easiest solution is to increase air flow from outside. This must be balanced with cost, because to increase air flow, your HVAC system must run longer. The minimum government standard devised by www.ashrae.org is 15 cubic feet/min of airflow per person in schools. Many systems just meet this standard for minimum cost. Energy recovery equipment can minimize the cost from increased ventilation airflow. Energy recovery is popular in Air conditioning in Denver and the east because the technology in this option saves money on large scale HVAC systems.

HVAC tech Motivation

In Colorado, HVAC engineers are members of a unique, specially recognized group. They belong to an international society for all individuals interested in precision climate control. They also conduct social work during the weekend to better the surrounding community. The society specializes in furnace repair in Denver for underprivileged and lower income families. It allows exchange of knowledge and experiences for the benefit journeyman appliance workers in Denver heating repair. They provide many opportunities to participate in the development of Denver air conditioning via, for example, the installation of air conditioning products in single Denver Heating and Air conditioning prides itself on paying union wages.

In lieu of profits some companies promote from within and offer free healthcare benefits with participating providers. In certain states, these courtesies are not extended to the common shop worker in air conditioning and heating profession. However, each employee that is hired for Denver furnace repair undergoes a strict 3-year background check. Local Building Permits are closely followed by Denver Heating contractors in public properties. Members are doused with the flame, which is a corporate tradition in which newly initiated employees are roasted from head to to with a localized propane torch to induce adherence to corporate guidelines. Some HVAC companies are looking at new ways to motivate their workers also offer a critically acclaimed employee assistance program for weigh loss to qualifying Denver Air Conditioning associates who have been with the company for 6 months or more.

One way techs get educated is through case examples and parables of employee behavior. One common education tactic is to take the employee through the refrigeration control system troubleshooting checklist. This is useful more for education, as modern refrigeration boards consist of solid state transistors. In such a case contact your Denver HVAC supplier to get a computer tech on the job. For older systems, this step by step ac checklist is a good confidence builder for air conditioning virgins. No matter how complicated a schematic is, control systems can only have a few outcomes from a given set of parameters. They can control: compressor or condenser fans, evaporator fans, line solenoids, or maintain a desired temperature. Whatever the component is, a great motivating tactic is to trace back the circuit to the switch that controls it. Once the tech sees where everything goes, his HVAC karma will be at one. If a solenoid drops to a set point the evaporator fan will run continuously. This simple solution should be evident once you have a trained HVAC technician.

Building Commissioning and HVAC Certification

Building commissioning is the process of ensuring all building HVAC systems work properly through one year of verification and documentation. Any large commercial HVAC system will need proper commissioning to ensure all systems are safe, working properly, and will pass Denver HVAC certification standards. Systems must work interactively with the owners according to the original design and intent to get this certification. Different jobs may have different levels of commissioning. Originally, the commissioning process was just making sure the building matched the original engineering specifications. Today, especially in socially conscious areas like Denver HVAC systems are often trying to achieve green building standards. Proper design and implementation can now save money as builders are trying to obtain tax breaks and increased sales through Green recognition. Not only in areas of efficiency, building commissioning is now holding contractors to a higher standard in electrical, health and safety systems, as well as overall building structural integrity. Commissioning is now involved in every aspect of the construction process, from design to training the operators of building systems. For green cities like Denver heating repair is not all that hard to accomplish and maintain standards. Those without HVAC contractors aware of green standards will have a harder time trying to commission a green building.

This is called total building commissioning. Obviously this adds cost to the project, but it also adds value to the property and may save money over time. The owner of a project will assign various responsibilities to the commissioning team based on trust and the difficulty of the project. The team may work with the HVAC contractor or with the owner.

A specialized commissioning engineer will work with your HVAC contractor in Denver from the beginning. A schedule of equipment testing will be worked out to determine when which piece of equipment will meet certain Denver heating and air conditioning standards. The commissioning team should review all documents to look for inconsistencies or flaws that could effect construction. Different commissioning plateaus will be assigned based on product arrival documents, proper function and testing. A large commercial HVAC job may even require factory testing before and at instillation. Training of operators should also be documented to insure they can operate all the functions of the building. Proper testing validates overall building design by testing functionality in various scenarios. Operating procedures for the use of equipment is a step in the commissioning process that helps ease the transition from construction to a fully functional site. The commissioning process is helpful from the heating contractor in that everything is documented. Any problems that arise later should be easier to identify, and liability will no longer be on the contractor.

Replacing a Thermostat: Wiring Colors

Replacing thermostat by yourself without a Denver HVAC technician can be pretty harrowing if you do not hook up the wiring correctly. Inside of the thermostat there are several terminals which must hook up with the right wires. The R-terminal is the thermostat's power. R means Red, the Colorado heating repairman should have red wires going to this terminal. This power comes from the transformer. The transformer is usually in the condensing unit or the air handler in a split system. Because they are supplying power, it is a good idea to kill the power to both the condenser and the air handler before working on the thermostat.

The RC terminal is the power for cooling. Some large HVAC systems have two transformers, one for cooling and one for heat. In such a case, the power from the ac system goes to the thermostat terminal. A jumper can be installed between RC and RH for a single transformer heating and cooling system. The RC terminal is also red.

The RH terminal is the heating power-in. This is also red and can be jumped to the RC.

The Y terminal is yellow and goes to the compressor relay. Some Denver HVAC specialists use a terminal board strip on the air handler control board which makes splices not needed. Y2 is usually light blue and is the code for a second stage cooler. If you do have two compressors, both should work off the same thermostat. Most Denver heating and air companies do not need the cooling of a two stage company.

W is the heating terminal. W is for white terminal. This should go directly to your heating source, whether it be a furnace or boiler. W2 is for second stage heat and is usually brown. This is for gas furnaces with low and high settings. Heat pumps use W2 for auxiliary heat.

G is for green and goes to the indoor blower fan relay.

C is for Common, and does not have a specific color although black is seen frequently. For digital thermostats that consume power, the common wire is necessary to complete the 24 volt circuit.

Orange "O" and "B" Blue are for heat pumps. Rheem and Ruud heat pumps use the B terminal for the cooling reversing valve. Other HVAC manufacturers use the O terminal. Trane, Lennox, Goodman, Ducane, Heil, Carrier, Fedders, Amana, and Janitrol are normally hooked up to the O terminal by HVAC contractors in Denver.

E is for emergency heating. This has no standard color but should be wired to the heating relay or E terminal strip board.

S1 and S2 are for outdoor air sensors. This has no standard color, but should use a shielded wire to reduce interference and the possibility of water damage from outside.

Warning: These colors are the defaults. The person wiring the thermostat could have used unconventional color coding.